Ah thanks, the telnet commands worked.
Hi Ger,
Thanks for your efforts. I tried to use it many time but it sometime worked for one day sometime for two day. But after 1.42 it works just for one min and when I add some torrents to it its UI disappears and my browser keep on looking for it infinitely. I know it is running and doing it job but I am not able to see it UI from PC or from gaya. Is there any way to roll it back to default version. I am really tired of trying it now. The default version was very stable.
Please help!!
Bhelpuri
(01-17-2009 01:03 PM)bhelpuri Wrote: [ -> ]Hi Ger,
Thanks for your efforts. I tried to use it many time but it sometime worked for one day sometime for two day. But after 1.42 it works just for one min and when I add some torrents to it its UI disappears and my browser keep on looking for it infinitely. I know it is running and doing it job but I am not able to see it UI from PC or from gaya. Is there any way to roll it back to default version. I am really tired of trying it now. The default version was very stable.
Please help!!
Bhelpuri
Too bad newer versions of Transmission don't work that well for you.
I would suggest a complete reinstall of the NMT Applications.
More information is
available here.
i tried the newer 150b version from your page.....donw/up speed were pretty well...far better than the oldest version especially down speed....BUT all newer version for me have the problem of update tracker....many times torrents stuck to updating status....(in prive trackers more than 3 and also in public trackers) i don't know why this happens but the problem is that when torrent is in updating status does not count the upload....also the only solution to continue the torrent is to stop it the torrent and start it again
ONLY version 1.40 work perfect and never had problem of updating torrent status....BUt this version has many other speed problem as all we know
thanks
Hi,
How can i limit the upload rate ? and how can i see which is the port use by transmission and change it ?
(i don't have telnet or ssh installed for the moment)
(01-17-2009 04:04 PM)Celos Wrote: [ -> ]Hi,
How can i limit the upload rate ? and how can i see which is the port use by transmission and change it ?
(i don't have telnet or ssh installed for the moment)
if you install
this to your PC you ll find all your answers
(01-17-2009 04:39 PM)giannis1010 Wrote: [ -> ]if you install this to your PC you ll find all your answers
Or just enable upload limit on the web ui
1. Go to http://PCH-A110:9091 (replace with correct ip adress)
2. Click the 'gear' button on the left bottom of you brower
3. Change settings like portnumber and up and download speeds.
(01-17-2009 04:39 PM)giannis1010 Wrote: [ -> ] (01-17-2009 04:04 PM)Celos Wrote: [ -> ]Hi,
How can i limit the upload rate ? and how can i see which is the port use by transmission and change it ?
(i don't have telnet or ssh installed for the moment)
if you install this to your PC you ll find all your answers
It works only with 1.4 or + and i have the defaut transmission version from the firmware...
Maybe if there is a thread which says how to update it ...
(01-17-2009 04:44 PM)Ger Teunis Wrote: [ -> ] (01-17-2009 04:39 PM)giannis1010 Wrote: [ -> ]if you install this to your PC you ll find all your answers
Or just enable upload limit on the web ui
1. Go to http://PCH-A110:9091 (replace with correct ip adress)
2. Click the 'gear' button on the left bottom of you brower
3. Change settings like portnumber and up and download speeds.
http://myPCHip:9091 doesn't work.
I have some problems with web access (see my thread:
http://www.networkedmediatank.com/showth...?tid=15138 )
(01-17-2009 04:49 PM)Celos Wrote: [ -> ]It works only with 1.4 or + and i have the defaut transmission version from the firmware...
Then why are you asking in a thread about 1.4+?
Anyway, the advise about doing it in the web interface is the same, and your other thread states you know how to access that on the frimware version of Transmission.
(01-17-2009 06:12 PM)vaivel Wrote: [ -> ]Then why are you asking in a thread about 1.4+?
Anyway, the advise about doing it in the web interface is the same, and your other thread states you know how to access that on the frimware version of Transmission.
My mistake ... i've just updated it to 1.42.
Seems to work fine, thanks.
Hi there:
I have problems too verifying a 30Gb torrent data. My PCH-A110 crashes and I have to reset. I started from a "clean" install.
- Format HD.
- Install NMT applications.
- Install Transmission 1.5 beta 1.
Regards & thanks in advance.
Updated the 1.50 to beta2
Downloads available on my site.
Also fixed a bug in Gaya interface which may cause it not to open correctly on some systems.
(01-17-2009 09:33 PM)Laertes Wrote: [ -> ]Hi there:
I have problems too verifying a 30Gb torrent data. My PCH-A110 crashes and I have to reset. I started from a "clean" install.
- Format HD.
- Install NMT applications.
- Install Transmission 1.5 beta 1.
Regards & thanks in advance.
The only suggestion I can make is to regularly test newer versions. I can download stable at reasonable speeds here using 1.50.
Is there a reason why 1.50beta2 isnt in the community installer?
(01-19-2009 12:12 AM)Ltmarx Wrote: [ -> ]Is there a reason why 1.50beta2 isnt in the community installer?
Yeah, because you didn't update your local repository file
It's there since today (few hours ago).
Have some ideas about transmission crash. Seems I have transmission crashes on my EGREAT M31B only if I have no speed limits. For example I try to run transmission without upload speed limit. Seems that if I have upload speed more than 400-450KB transmission crashes. The same result for download speed. Now I set download limit to 1000KB. Will try with 1.50 beta2.