[C-200] Firmware 03-04-110530-21-POP-408 (03-04-110520-21-POP-408 Apps) (3.06.2011)

[werner]

OPTIONAL STEPS ONLY IF YOU USE USERAPPS!!!!!

Quote:1. unistall LTU package with the CSI App!! (if you don't have it installed then start with Step 2)
removing the HDD won't work because maybe the LTU change also parts inside the NAND.

* LTU is a UserApp CSI package that when installed fixes FTP freezing. However like all UserApps they can interfere with Syabas's firmware and update process. Therefore if you use any CSI UserApps it is best to disconnect the location of them, be it HDD or USB stick. Search the WIKI for a CSI if you dont know what the CSI is. The next firmware should have the updated versions of pureFTP etc. that the LTU package brings.

2. unplug your HDD where your NMT Apps are installed!

3. update firmware to 110422 again (update the same firmware with USB)
http://www.networkedmediatank.com/showth...?tid=51992

4. clear cache, restore factory setting, reboot
clear cache: goto Setup=>Maintenance and press the filemode button on your Remote
restore factory defaults: goto Setup=>Maintenance and press on "reset to factory settings"

5. Open a ticket and wait for the MAC unblock
1.) register at http://support.popcornhour.com
2.) sign in
3.) under "My Products" add your C200
4.) under "My Cases" open a "New Case"
5.) choose under "Product" your C200
6.) at "Brief Description" add in "Err059 Mac Adress Reset"
7.) at "Details of Question or Problem" you can enter the following

Quote:MAC Adress: 00:00:00:00:00 (replace that with the MAC from your C200)

Hello i tried to flash the C200 stepstone firmware, it failed and showed me ERR059, according to the forum, please Reset my Mac Adress

Regards,
NAME

6. do the online update again
if you get again ERR00064.217 then you don't need to try again and again you have to do STEP 5 again.

7. do the online update again
if you get again ERR00064.217 then you don't need to try again and again you have to wait then again that the mac gets resetted!!!

Regards,
Werner

OPTIONAL STEPS IF YOU USE USERAPPS!!!!!

Quote:

!!! STEPSTONE FIRMWARE !!!
!!! after installing this firmware, you won't be able to downgrade to any older firmware anymore !!!
This firmware updates your BluRay license and will enable Blurays using newer versions AACS protection to now play. Every 18 months the Bluray license requires updating. These license updates will always be stepstone updates and in order to receive future firmware updates you MUST step through this update, therefore the naming StepStone!!!

Dear customers,

Please be informed that Popcorn Hour C-200 firmware:
03-04-110530-21-POP-408-000
and NMT apps:
03-04-110520-21-POP-408
is available for update.

Goto Setup->Maintenance->Check for firmware update

NMT Apps Offline package:
  03-04-110520-21-POP-408.zip (Size: 19.28 MB / Downloads: 6133)

!!! after installing this firmware, you won't be able to downgrade to any older firmware anymore !!!
!!! STEPSTONE FIRMWARE !!!

RELEASENOTES FIRMWARE

Code:

Release date : 3 June 2011
Firmware version : 03-04-110530-21-POP-408-000

**********************************************************
* !!! Note that with this firmware onwards, you will     *
* NOT be able to downgrade to older firmware anymore !!! *
**********************************************************

1. New NMT apps 03-04-110520-21-POP-408
2. Minimum firmware version to update to this is 02-04-110422-21-POP-408-000
3. BD/AVCHD/DVD/CDDA
   - Renewal of AACS key
   - Audio enabled for BD PiP now, output as multi-channel PCM
     Known issue: unable to output via SPDIF

================================================================================​===========

NMT Apps Version : 03-04-110520-21-POP-408

Release Notes :
1. Minimum firmware version to use this NMT App is 03-04-110530-21-POP-408-000
2. Version stepping, practically same as 02-04-101104-21-POP-408

BD Playback without internal HDD

Quote:1.) Format an USB Stick with 2GB or more to ntfs,fat32 or ext3
2.) Plugin the Stick
3.) Now you can playback BD's with BD-J and BD Live

Quote:IMPORTANT: THIS WORK ONLY 5 TIMES IN EACH OF THE SETUPS!
DVD Region Setting:
1.) Insert an DVD Disc which has the Region you wanna setup, if the Region is not the same as the Disc has, it wont work!
2.) Please go into the Setup Page
3.) press now "Slow, 1, 6, 8, 3" on your remote (SLOW means the |> Button on the Remote)
4.) now an popup shows up, on the remote use the number for the region you wanna set.

[quote]1 Canada, United States; U.S. territories; Bermuda
2 Western Europe, incl. United Kingdom, and Central Europe; Western Asia; including Iran, Israel and Turkey, Egypt; Japan, South Africa, Swaziland, Lesotho; French overseas territories
3 Southeast Asia; South Korea; Taiwan; Hong Kong; Macau
4 Mexico, Central and South America; Caribbean; Australia; New Zealand; Oceania;
5 Ukraine, Belarus, Russia, Continent of Africa, excluding Egypt, South Africa, Swaziland, and Lesotho; Central and South Asia, Mongolia, North Korea.
6 People's Republic of China, Hong Kong

BD Region Setting:
1.) go into Setup (no need to put an BluRay into the drive)
2.) press now "Slow, 1, 6, 6, 3" on your remote (SLOW means the |> Button on the Remote)
3.) an popup shows up, on the remote use the number keys to select the region you need.

Quote:1 = Region A
2 = Region B
3 = Region C

[Willem53]

Question for those who get ERRO59.....

Do you have CSI LTU installed?

My update went smooth after un-installing LTU, I would like to make sure if that was coincidence or cause...

[accident]

You didn't really ask this but to add to your list, I did not have csi installed at all. I was a firmware+nmt setup and I worked the first time (within about 10 mins of the update being posted on the forum).

[Poslanec]

(06-06-2011 08:17 PM)Willem53 Wrote:  Question for those who get ERRO59.....

Do you have CSI LTU installed?

My update went smooth after un-installing LTU, I would like to make sure if that was coincidence or cause...

For the first time tried to update with disabled HDD with LTU, later - with the included HDD. ERRO59 remained in both cases.
There are those who have upgraded with the established LTU

[werner]

Hi willem thats very interresting, i totally forget about that.

1. unistall LTU package with the CSI App!!
removing the HDD won't work because LTU change also parts inside the NAND which is firmware part!!!

2. unplug your HDD where your NMT Apps are installed!

3. update firmware to 110422 again (update the same firmware with USB)
http://www.networkedmediatank.com/showth...?tid=51992

4. clear cache, restore factory setting, reboot
clear cache: goto Setup=>Maintenance and press the filemode button on your Remote
restore factory defaults: goto Setup=>Maintenance and press on "reset to factory settings"

5. wait for the MAC unblock
i will post a message here if our engineer resetted the failed macs again.

6. do the online update again
if you get again ERR00064.217 then you don't need to try again and again you have to wait then again that the mac gets resetted!!!

Regards,
Werner

(06-06-2011 08:17 PM)Willem53 Wrote:  Question for those who get ERRO59.....

Do you have CSI LTU installed?

My update went smooth after un-installing LTU, I would like to make sure if that was coincidence or cause...

[werner]

Thread closed now again and cleaned, will reopen it when the failed macs are resetted again, please the view users were it failed, follow the steps in this thread ore also one post over this, if you don't have any CSI Apps installed then please start with Step 2 and please wait that i post a message that the MAC is resetted!!

Regards,
Werner

[werner]

The failed Mac Addresses are reset now, so please try the steps now posted at the first post.

Regards,
Werner

[geekuix]

Update successful! Thanks a lot

[Bloodsack]

To update do I have to follow these steps? or should I wait for a fw fix? If one is coming?

[geekuix]

follow the step on the top it should work

[werner]

there won't come a firmware fix, because the firmware has no issue! currently it seems that some user packages, currently we know only about LTU, is causing the update issue.

[Padavan]

werner
New firmware has really issue when checking firmware hack (e.g. cross-firmware checking)

LTU not performed any firmware hacking, LTU only write on:
initramfs (extracted in the RAM)
/nmt (first partition in NMT storage, update pure-ftpd and transmission)
/share (last partition in NMT storage, used CSI dir Apps)
some settings ("btpdserv 0"/"btpdserv 1")

It is all!

After remove NMT storage and reboot PCH, firmware returned in original state. Today, after this operations, after cleaning cache and reset settings to default, my firmware update is completed successfull.

[tinnef]

That did the trick. Still I'm curious what exactly the problem was, previously I have updated with LTU installed (might have been an older version, can't remember) , so something, somewhere has changed. I would hate to have to perform this whole routine with every update.

[werner]

hi padavan, we think LTU is using the memory location which is needed for the key programming, thats the reason for the failed updates, we have confirmation from 5 users now that it works after removing the LTU package.

[werner]

there won't be issues with later firmwares, because the difference with this build is that it needs to program the key which happens online, for which it needs memory which is used by the LTU package.

(06-07-2011 07:37 AM)tinnef Wrote:  That did the trick. Still I'm curious what exactly the problem was, previously I have updated with LTU installed (might have been an older version, can't remember) , so something, somewhere has changed. I would hate to have to perform this whole routine with every update.